マックス鉄筋結束機 TWINTIER
RB401T-E
Ergonomic solution for backbreaking slab work
The RB401T-E is ergonomically designed to reduce back strain. The extended frame allows you to stand-up and tie rebar for concrete slabs.
-
Combination of 2 rebars
-
Combination of 3 rebars
-
Combination of 4 rebars
RB401T-E Features and Benefits
REDUCES BACK STRAIN
Changes in lumbar compression force during tying
Up to88%
Less Effort
Compared to Manual Tying the RB401T-E used less energy consumption when tying rebar. This makes tying with the RB401T-E that much easier and allows more work to get done.
Up to55%
Calculated Reduction In Compression Force
Based on the recorded force between hand tying and the RB401T-E, accumulated force using pliers is calculated to exceed NIOSH’s first risk zone for developing lumbar spondylosis (back pain) after 5 years.
*Based on NIOSH’s Health Hazard Evaluation calculations, reaching cumulative compression of 6.0E+06N(N・Hr)puts a worker at risk of developing lumbar spondylosis≥ Odds Ratio (OR) = 2.6 (95% CI 1.2-5.7).
*Calculated based on average newtons (N) recorded while tying in both methods tested by MAX.
*Calculations based on 3hrs tying/ day.
*NIOSH’s first risk zone for developing lumbar spondylosis is any cumulative Newtons above 6.0E+06N(N・Hr).
Simulated by 
Simulated “Lumbar compression force” by modeling simulation software (Anybody).
AnyBody Modeling System™ is the registered trademarks of AnyBody Technology A/S in Denmark, the U.S. and/or other countries.
ERGONOMIC DESIGN
Trigger-less Technology
No trigger pulling
on this tool.
An automatic contact mechanism allows the tool to instantly tie when pushed down over a rebar intersection.
Smooth rebar guide system
Easy insertion into rebar intersections
Long nose attachment guides the tool mouth to slide the contact switch into the rebar with ease.
Adjustable handles
Handles are adjustable to
2 positions
Two handles make it easy to lift and maneuver the tool across the slab.
When holding the tool your hands should be positioned at the waist level
SAME TWINTIER SYSTEM BENEFITS
Same 14.4 Battery and
19Ga TW1061T platform
OTHER KEY DETAILS
Nose Attachment
| Rebar Size | Clearance needed under rebar for long attachment | Clearance needed under rebar for short attachment |
| #3 x #3 | 2-1/8" | 1-3/8" |
| #4 x #4 | 1-7/8" | 1-1/8" |
| Rebar Size | Clearance needed under rebar for long attachment | Clearance needed under rebar for short attachment |
| #3 x #3 | 2-1/8" | 1-3/8" |
| #4 x #4 | 1-7/8" | 1-1/8" |
Two Nose
Attachments
There are two nose attachments available depending on the clearance between the rebar and the ground.
Replaceable
Nose attachment
Once a nose is worn out, simply replace the
attachment. No need for repair.
Torque dial
Torque dial conveniently located for easy adjustment
Adjust the dial to suit the tying application.
Reset to clear wire jams
Easy to clear wire jams.
Wire jams are easily cleared by turning the tool OFF and ON.
Operational Manual Video
SPEC
| DESCRIPTION | RB401T-E |
|---|---|
| WEIGHT | 10.2lbs |
| DIMENSIONS (H x W x L) |
12-3/4" × 16-1/16" × 43-1/4" |
| APPLICABLE REBAR | #3 x #3 - #6 x #6 (up to #5 x #5 + #4 x #4) |
| TYING SPEED | Apprx. 1/2 seconds |
| TIES PER CHARGE | 4000 |
| AVAILABLE TIE WIRE | TW1061T, TW1061T-EG, TW1061T-PC, TW1061T-S, TW1061TUSA |
TIEWIRE
| DESCRIPTION | TW1061T | TW1061T-EG | TW1061T-PC | TW1061T-S |
|---|---|---|---|---|
| MATERIAL AND COATING | Annealed wire | Electro-galvanized wire | Poly-coated wire | Stainless Steel wire |
| GAUGE | 19Ga | 19Ga | 19Ga | 19Ga |
| DESCRIPTION | TW1061T |
|---|---|
| MATERIAL AND COATING | Annealed wire |
| GAUGE | 19Ga |
| DESCRIPTION | TW1061T-EG |
|---|---|
| MATERIAL AND COATING | Electro-galvanized wire |
| GAUGE | 19Ga |
| DESCRIPTION | TW1061T-PC |
|---|---|
| MATERIAL AND COATING | Poly-coated wire |
| GAUGE | 19Ga |
| DESCRIPTION | TW1061T-S |
|---|---|
| MATERIAL AND COATING | Stainless Steel wire |
| GAUGE | 19Ga |
